Application and function

Schlüter-DESIGNBASE-SL is a high-quality profile to quickly create skirting covers. 

Schlüter-DESIGNBASE-SL-A, made of high-quality colour coated or anodised aluminium, is available in heights of 60 and 80 mm.

Schlüter-DESIGNBASE-SL-E, made of brushed stainless steel (V2A), is available in heights of 110 and 160 mm. 

The profile is attached to wall areas with a suitable installation adhesive (e.g. Schlüter-KERDI-FIX). Optionally, it can be fitted with a sealing lip that is available as an accessory to protect the edge joint from moisture and to reduce the transmission of impact sound. The DESIGNBASE-SL assortment also includes matching internal and external metallic corner pieces and end caps to easily create visually appealing connections.

Installation

1. Adhere Schlüter-DESIGNBASE-SL with the installation adhesive KERDI-FIX or an equivalent material. Apply a sufficient number of adhesive spots on the reverse of the profile – above and below the spacer in the case of DESIGNBASE-SL-E; see illustration – and set the profile in place.
   Remove any substances that may inhibit bonding, such as grease etc. prior to applying the installation adhesive.
   Note: Optionally, the profile can be fitted with a sealing lip that is available as an accessory (see drawing) to protect the edge joint from moisture and to reduce the transmission of impact sound. The sealing lip is pressed firmly into the profile from the front for the aluminium variant, or clipped on from the back for the stainless steel variant, so that its front edge is flush with the profile (see drawing for correct/incorrect installation).
    
2. Remove any excess adhesive with a suitable cleaning product.

Material

Schlüter-DESIGNBASE-SL is available in the following materials:

• AE = Anodised aluminium
• AEEB = Brushed stainless steel effect anodised aluminium
• AC = Colour coated aluminium
• EB = Brushed stainless steel (V2A)
  material no. 1.4301 = AISI 304

Material properties and areas of application:

In special cases, the suitability of the profile must be verified, based on the anticipated chemical or mechanical stresses. The information provided below is intended as a general guideline.

Anodised aluminium: The aluminium features an anodised finish that retains a uniform appearance during normal use. Damage to the anodised surfaces can be restored with paint. Surface areas must be protected against abrasion or scratching. Aluminium is sensitive to alkaline media. Cementitious materials, in conjunction with moisture, become alkaline, which may result in corrosion depending on the concentration and length of exposure (aluminium hydroxide formation).
For this reason, remove adhesive or grouting material immediately from all visible areas and do not cover freshly installed coverings with foil.

Colour coated aluminium: The aluminium is pre-treated (chrome plated) and powder- coated with a polyurethane covering. The coating is colour-stable, as well as UV-and weather-resistant. Visible edges should be protected against abrasion.

Stainless steel: Stainless steel can withstand high mechanical stress and is highly resistant against chemicals. Even stainless steel of quality 1.4301 is not resistant to all chemical stresses. Substances such as hydrochloric or hydrofluoric acid or certain chloride and brine concentrations may cause damage. Consideration of anticipated chemical stresses should therefore be verified in advance.

Note

Schlüter-DESIGNBASE-SL requires no special maintenance or care. Do not use abrasive cleaning agents on the sensitive surfaces.

Damage to the anodised surfaces can be restored with paint. All cleaning agents must be free of hydrochloric and hydrofluoric acid. Regularly treat stainless steel surfaces with a polish such as Schlüter-CLEAN-CP to retain their shine.

Products

• Schlüter®-DESIGNBASE-SL-AE
• Schlüter®-DESIGNBASE-SL-AEEB
• Schlüter®-DESIGNBASE-SL-AC
• Schlüter®-DESIGNBASE-SLZ (sealing lip)
• Schlüter®-DESIGNBASE-SL-E