Schlüter®-QUADEC-FS | Function | Schlüter-Systems
logo

Schlüter®-QUADEC-FS

Application and function

Schlüter®-QUADEC-FS is a border profile for creating visually appealing designs in interior wall coverings. These profiles can be combined with the corresponding Schlüter®-QUADEC profiles for outside wall corners. Schlüter®-QUADEC-FS has two visible surfaces, approximately 10 mm wide. The 50 mm open space of the profile can accept tiles to match the wall design or other materials as a contrasting insert. The aluminium profiles, which are available in a wide range of finishing options, allow for decorative design and create interesting visual contrasts.


Schlüter®-QUADEC-FS

Installation

  1. Schlüter®-QUADEC-FS can be used in flush assemblies with tiles that are thicker than 11 mm. If thinner coverings are used, the profile protrudes over the adjoining covering.
  2. Install the tile covering up to the location where Schlüter®-QUADEC-FS is to be installed as a decorative strip. Apply a sufficient amount of tile adhesive to this location or the back of Schlüter®-QUADEC-FS and embed the profile in such a way that the visible surfaces are flush with the adjoining tile covering or protrude evenly over it. 
  3. Install the next adjoining row of tiles, leaving a space of approx. 2 mm between the tile and the profile for grouting.
  4. Use suitable materials and tools for the sensitive surfaces to avoid scratches or other damage. Mortar and tile adhesive should be removed immediately.
  5. Matching preformed inside and outside corner pieces are available

Schlüter®-QUADEC-FS

Material

Schlüter®-QUADEC-FS is made of aluminium and is available in a variety of anodised surface finishing options.

Material properties and areas of application
The suitability of Schlüter®-QUADEC-FS must be verified based on the anticipated chemical stresses. Aluminium is sensitive to alkaline media. Cementitious materials, in conjunction with moisture become alkaline. Since aluminium is sensitive to alkaline substances, exposure to the alkali (depending on the concentration and duration of exposure) may result in corrosion (aluminium hydroxide formation).

Therefore, it is important to immediately remove mortar or grout residue from visible surfaces. In addition, ensure that the profile is solidly embedded in the setting material. Schlüter®-QUADEC-FS profiles have an anodised surface layer that retains a uniform appearance during normal use. The surface must be protected against abrasion.


Schlüter®-QUADEC-FS

Maintenance

The visible surface of Schlüter®-QUADEC-FS requires no special maintenance or care. Do not use abrasive cleaning agents on the sensitive surfaces. Damaged anodised surfaces can be restored with paint.


Schlüter®-QUADEC-FS

Products


Schlüter®-QUADEC-FS

* to complete the Art.-No., add the surface finish (e.g. QF 8/50 AT).
Surface finish:
AE - anodised aluminium
AT - aluminium/titanium


Schlüter®-QUADEC-FS/E

Note: The variable corner pieces can be used for internal and external corners.


Schlüter®-QUADEC-FS

Download


Contact Schlüter-Systems Ltd

Units 3-5 Bardon 22,
Beveridge Lane, Coalville,
Leicestershire, LE67 1TE
Phone: +44 (0) 1530 813396

Quick contact list

Reach the department of your choice directly via email:

image
Write To Us!

Do you have a question or suggestion?

Further information

on our products and specifications can be found here:

Metal surfaces
Metal surfaces

All surfaces at a glance

Legend "Products"

We use the following symbols and abbreviations to illustrate our price charts.

image image

= new products

= radius perforation available   

 

Dimensions:
H = height
L = length
B = width


Packaging:
PL = euro pallet 
KV = case packaging 
BV = bundle (there is a 10 item bundle packaging for all the profile types)
P = box packaging 
R = roll
St. = unit