Schlüter®-LIPROTEC-LL | Schlüter-Systems
logo

Schlüter®-LIPROTEC-LL

Application and function

Schlüter-LIPROTEC-LL is a high-quality support profile made of anodised aluminium for the attachment of various LED strips Schlüter-LIPROTEC-ES. The profile is designed to create accent lighting in wall coverings in the form of a straight light line. Schlüter-LIPROTEC-LL is particularly well suited to highlight niches or shelf structures and elements. The placement of the profile creates direct or indirect lighting effects.

For illumination, the selected LED strip Schlüter-LIPROTEC-ES is adhered within the U-shaped profile and covered with the corresponding diffuser lens. All profiles of the Schlüter-LIPROTEC series allow for the replacement of diffuser lenses and luminaires, including after installation.

Matching end caps are available as accessories.

Schlüter-KERDI-BOARD-K installation modules with pre-cut grooves for profile attachment and Schlüter-LIPROTEC-ZKK cable ducts are available for easy installation.

Note: Schlüter-LIPROTEC-LLP is a pre-assembled LED module made from a flexible, encapsulated LED strip with homogeneous light distribution and the attachment profile Schlüter-LIPROTEC-LL.


Schlüter®-LIPROTEC-LL

Installation

Note: Please observe the installation instructions for Schlüter-LIPROTEC for the attachment of the lighting components and for the layout and positioning of wiring.

  1. Install the tile covering to the height at which Schlüter-LIPROTEC-LL is to be installed as a light line.
  2. Drill a cable conduit through the profile and deburr the opening.
  3. Adhere Schlüter-LIPROTEC-LL with the installation adhesive Schlüter-KERDI-FIX or an equivalent product. Apply a line of adhesive on the reverse face outer surface of the profile and set it in place. Remove all substances, lubricants etc. that may weaken the bond from the adhesive areas prior to applying the sealant.
  4. Remove any excess adhesive that is squeezed out underneath the profile with a suitable detergent.
  5. Now install the next adjoining row of tiles.
  6. Leave a joint of approximately 1.5 mm to the profile. Completely fill the space between the tile and the profile with grout.
  7. Use suitable materials and tools for the sensitive surfaces to avoid scratches or other damage. Residue of mortar and tile adhesive should be removed immediately.
  8. Corner formations must be created with mitre cuts.

Schlüter®-LIPROTEC-LL

Material

Schlüter-LIPROTEC-LL is available in the following material versions:

Profile:

  • AE = anodised aluminium

Diffuser lens:

  • PMMA = polymethyl methacrylate

Material properties and areas of application:

In special cases, the suitability of the profile must be verified based on the anticipated chemical and mechanical stresses.

The information provided below is intended as a general guideline.

Schlüter-LIPROTEC-LL (anodised aluminium): The aluminium features an anodised finish that retains a uniform appearance during normal use. Damaged anodised surfaces can be restored with paint. Visible surfaces should be protected against abrasion.

Aluminium is sensitive to alkaline media. Cementitious materials, in conjunction with moisture, become alkaline. Depending on the concentration and duration of exposure, this may result in corrosion (aluminium hydroxide formation).

For this reason, remove mortar or grouting material immediately from all visible areas and do not cover freshly installed coverings with polythene or similar.

Schlüter-LIPROTEC diffuser lenses consist of a lightly structured, translucent thermoplastic PMMA material (polymethyl methacrylate). Alcohol (e.g. rubbing alcohol) or detergents with surfactant content over 5% may cause damage to the diffuser lens.

Note: The profiles with their diffuser lenses must be positioned in such a way that no water can accumulate within the profile.


Schlüter®-LIPROTEC-LL

Note

Schlüter-LIPROTEC-LL requires no special maintenance or care. Do not use abrasive cleaning agents on the sensitive surfaces. Damaged anodised surfaces can be restored with paint. All cleaning agents must be free of hydrochloric and hydrofluoric acid. Alcohol (e.g. rubbing alcohol) or detergents with surfactant content over 5 % may cause damage to the diffuser lens.

Because of minor heat development of the LED strips used in the profile, the expansion of the profile and the utilised diffuser lens may differ.


Schlüter®-LIPROTEC-LL

Products


Schlüter-LIPROTEC-LL


Schlüter®-LIPROTEC-WSI


End caps Schlüter®-LIPROTEC-WS/EK

End caps Schlüter®-LIPROTEC-WS/EK


Schlüter®-KERDI-BOARD-K

Schlüter-KERDI-BOARD-K are installation modules with pre-cut grooves for accommodating Schlüter-LIPROTEC cable ducts. The groove is designed to also accommodate a 19 mm Schlüter-KERDI-BOARD or the Schlüter-LIPROTEC-LL carrier profile.

Schlüter®-KERDI-BOARD-K


Schlüter®-LIPROTEC-LL


Contact Schlüter-Systems Ltd

Units 3-5 Bardon 22,
Beveridge Lane, Coalville,
Leicestershire, LE67 1TE
Phone: +44 (0) 1530 813396

Quick contact list

Reach the department of your choice directly via email:

image
Write To Us!

Do you have a question or suggestion?

Easy light control from any location

Find out more about the Schlüter apps.

Metal surfaces
Metal surfaces

All surfaces at a glance

Legend for product tables

We use the following symbols and abbreviations to ensure a uniform and clear layout of the tables:

image image image

= new products

= also with a length of 3 m

= radius perforations available   

 

Dimensions:
H = height
L = length
B = width
T = depth


Legend:
PL = euro pallet
KV = case packaging
BV = bundle (10 units)
P = box packaging
R = roll
St. = unit


Schlüter®-LIPROTEC

Learn more about Schlüter-LIPROTEC on our microsite.