Schlüter®-BARA-RWL | Function | Schlüter-Systems
logo

Schlüter®-BARA-RWL

Application and Function

Schlüter®-BARA-RWL is an L shaped finishing profile for large format pavers, which are laid on loose gravel layers or pedestal assemblies above a waterproofing layer (in accordance with DIN 18195-5) and installed drainage layer.

The trapezoid perforated anchoring leg of Schlüter®-BARA-RWL is placed along the edge, on top of the waterproofing layer and adjusted to the correct height and alignment. The vertical finishing leg covers the edge of either the entire surface assembly or just the gravel layer or pedestals. Profile heights from 15 mm to 150 mm allow for any type of edge formation.

Drainage holes, spaced at approximately 7.5 cm, are incorporated at the transition of the anchoring leg and the finishing leg to ensure the correct drainage of any collecting seepage water.


Schlüter®-BARA-RWL

Installation

  1. Select Schlüter®-BARA-RWL according to the height of the floor construction to be covered. A prefabricated corner piece is available for external corners. Abut the profile ends of Schlüter®-BARA-RWL, leaving a joint of approximately 5 mm. Cover the joint with the snap on connector.
  2. Before the drainage mats (Schlüter®-TROBA or Schlüter®-TROBA-PLUS) are installed, set the trapezoid perforated anchoring leg of the finishing profile, Schlüter®-BARA-RWL, onto the waterproofing layer and, if required, adjust to the correct height and alignment with dabs of mortar.
  3. a)If Schlüter®-BARA-RWL is used as a gravel containment profile, the gravel should reach just below the upper edge of the vertical profile leg, depending on the thickness of the covering. The gravel or crushed stone must be contained to stabilise this edge area. The next step is to install the concrete pavers loosely on the levelled gravel bed.
    b) If Schlüter®-BARA-RWL is used as a finishing profile for pedestal supported coverings, the profile covers the exposed edge of the covering assembly. In this case, the exterior casting mould rings Schlüter®-TROBA-STELZ are installed on top of the drainage mat Schlüter®-TROBA-PLUS 8G in the area of the trapezoid perforated anchoring legs of Schlüter®-BARA-RWL. Then, install the concrete pavers over the casting mould rings.

 

Note: To allow for unobstructed water drainage in the edge area of the covering assembly, it must be assured that the drainage openings of the drainage membrane remain open during installation.


Schlüter®-BARA-RWL

Material

Schlüter®-BARA-RWL is available in colour coated aluminium.

Material properties and areas of application
Schlüter®-BARA-RWL consists of colour coated aluminium, which is roll formed from aluminium sheets.

The coating of the aluminium profile is colourfast, weather resistant and UV resistant. Visible surfaces should be protected against abrasion.

In special cases, the suitability of Schlüter®- BARA-RWL must be verified based on the anticipated chemical, mechanical and/or other stresses.


Schlüter®-BARA-RWL

Maintenance

Schlüter®-BARA-RWL requires no special maintenance or care. The coated surface of the aluminium profile is colourfast and UV resistant. Damaged visible surfaces can be restored with paint.


Schlüter®-BARA-RWL


Schlüter®-BARA-RWL

Note: For external and internal corners see Schlüter®-BARA-RW.

* to complete the Art.-No., add the colour (e.g. RWL 120 PG).

Colours:
GM - grey metallic, RAL 9006
PG - pastel grey, no RAL


Schlüter®-BARA-RWL


Contact Schlüter-Systems Ltd

Units 3-5 Bardon 22,
Beveridge Lane, Coalville,
Leicestershire, LE67 1TE
Phone: +44 (0) 1530 813396

Quick contact list

Reach the department of your choice directly via email:

image
Write To Us!

Do you have a question or suggestion?

Further information

on our products and specifications can be found here:

Schlüter colour key
Schlüter colour key

From brilliant white to brick red - here you will find an overview of all available product colours.

Legend "Products"

We use the following symbols and abbreviations to illustrate our price charts.

image image

= new products

= radius perforation available   

 

Dimensions:
H = height
L = length
B = width


Packaging:
PL = euro pallet 
KV = case packaging 
BV = bundle (there is a 10 item bundle packaging for all the profile types)
P = box packaging 
R = roll
St. = unit  


Schlüter® profiles with radius perforations
Schlüter® profiles with radius perforations