Installation of Schlüter®-BARA-RTKE
- Select Schlüter®-BARA-RTKE according to the tile thickness.
- As a finishing profile and gutter attachment profile (for Schlüter®-BARIN), Schlüter®- BARA-RTKE is embedded into the thinbed mortar setting material with the trapezoid perforated anchoring leg aligned at the edge of the screed. Completely cover the anchoring leg with mortar.
- Install Schlüter®-KERDI over the anchoring leg and cover the undercut profile of the protruding adhesive flange of Schlüter®- BARA-RTKE using the sealing adhesive Schlüter®-KERDI-COLL.
- If using a trowel applied waterproofing compound, align the trapezoid perforated anchoring leg of Schlüter®-BARA-RTKE in the waterproofing assembly at the exposed edge. The waterproofing material must cover the undercut profile of the protruding adhesive flange. Observe the installation instructions of the manufacturer for the installation of bonded waterproofing systems.
- The bonded drainage membrane Schlüter®-DITRA-DRAIN is adhered over the bonded waterproofing assembly. Make sure to continue the membrane to below the joint spacer integrated in the profile. The profile height 23 mm is also suitable for use with Schlüter®-DITRA-DRAIN 8. It must be ensured that the drainage space is not fully closed, including during the installation of the covering materials.
- The system is now ready for the installation of tiles in the thin-bed method, observing the installation instructions of data sheet 6.2 Schlüter®-DITRA-DRAIN. Maintain a proper joint between the tiles and the anchoring leg of Schlüter®-BARA-RTKE, to be filled with suitable elastomeric sealing compound.
- After the completion of the covering, the gutter system can be attached to the Schlüter®-BARA profile, using the supplied screws. The elongated holes allow for attaching the gutters at a slope.
- Note:
Preformed parts are available for inside and outside corners. Abut the profile ends of Schlüter®-BARA-RTKE, leaving a gap of approx. 5 mm and cover the gap with the clip on connector. The applicable installation instructions and guidelines for the covering assemblies must be observed. All materials used in the assembly must be weather resistant, waterproof, and suitable for outdoor areas.
Installation of Schlüter®-BARA-RTKEG
- Select Schlüter®-BARA-RTKEG according to the tile thickness.
- As a finishing profile and gutter attachment profile (for Schlüter®-BARIN), Schlüter®-BARA-RTKEG is embedded into the thin-bed mortar with the trapezoid perforated anchoring leg aligned at the edge of the screed. Completely cover the anchoring leg with mortar.
- Install Schlüter®-DITRA 25, abutting the anchoring leg. The connection with the profile is established with the sealing tape Schlüter®-KERDI-KEBA. Use the sealing adhesive Schlüter®-KERDI-COLL to attach the sealing tape with an overlap of at least 5 cm on Schlüter®- DITRA 25, covering the entire anchoring leg and overlapping the undercut profile of the protruding adhesive flange of Schlüter®-BARA-RTKEG. The system is now ready for the installation of tiles in the thin-bed method, observing the installation instructions of data sheet 6.1 Schlüter®-DITRA 25. Maintain a proper joint between the tiles and the anchoring leg of Schlüter®-BARA-RTKEG, to be filled with suitable elastomeric sealing compound.
- If using a trowel applied waterproofing compound, align the trapezoid perforated anchoring leg of Schlüter®-BARA-RTKEG in the waterproofing assembly at the exposed edge. The waterproofing material must cover the undercut profile of the protruding adhesive flange. Observe the installation instructions of the manufacturer for the installation of bonded waterproofing systems.
- After the completion of the covering, the gutter system can be attached to the Schlüter®-BARA profile, using the screws supplied. The elongated holes allow for attaching the gutters at a slope.
Note: Preformed parts are available for inside and outside corners. Abut the profile ends of Schlüter®-BARA-RTKEG, leaving a gap of approx. 5 mm and cover the gap with the clip on connectors. The applicable installation instructions and guidelines for the covering assemblies must be observed. All materials used in the assembly must be weather resistant, waterproof and suitable for outdoor areas.