Cookies on the Schlüter-Website

Cookies help us deliver our services. By using our services, you agree to our use of cookies. Further information

logo

Schlüter®-BARA-RT

Installation

Installation with self-supporting pavers on mortar contact points or gravel/crushed stone beds

  1. Select Schlüter®-BARA-RT according to the thickness of the edge area to be covered. Pre-formed corners are available for external corners. A distance of approx. 5 mm should be left between profile ends, with the gap covered by clip-on connectors.
  2. Embed the trapezoid perforated anchoring leg of the angled edging profile Schlüter®-BARA-RT in a contact point of thin screed on top of the previously installed drainage membrane, Schlüter®-TROBA-PLUS, and align it horizontally and vertically. When installing over gravel, the Schlüter®-TROBA drainage mat is installed first, followed by Schlüter®-BARA-RT in the screed.
  3. 1.When using Schlüter®-BARA-RT as a gravel retaining edge, the gravel should reach just below the upper edge of the vertical profile leg, depending on the thickness of the covering. Now the concrete pavers are loosely installed on the levelled gravel bed.
    2. When installing on top of Schlüter®- TROBA-PLUS with thin bed moulding rings, Schlüter®-TROBA-STELZ-DR, the Schlüter®-BARA-RT finishing profile will cover the exposed edge of the assembly. The outside thin bed contact points are positioned on the trapezoid perforated anchoring leg of Schlüter®- BARA-RT.
    3. The self supporting pavers are then laid onto the contact points. When using the stilted construction with Schlüter®- TROBA-STELZ-MR, the profile Schlüter®-BARA-RT is integrated into the mortar point. The finishing profile covers the exposed edge of the cover assembly. The self supporting pavers are then installed on top of the stilted construction.

 

Note: A sufficiently large space for drainage must be provided to allow for unobstructed water drainage in the edge area of the cover assembly.

Installation in conjunction with tile coverings

  1. Select Schlüter®-BARA-RT according to the thickness of the edge area to be covered. Pre-formed corners are available for external corners. A distance of approx. 5 mm should be left between profile ends, with the gap covered by clip-on connectors.
  2. Embed the trapezoid perforated anchoring leg of the edging profile Schlüter®- BARA-RT on the edge of the screed or on the previously installed drainage mat Schlüter®-DITRA-DRAIN by placing it into the contact layer of thin set adhesive and trowel additional adhesive over the leg so that it is completely covered.
  3. If using Schlüter®-DITRA 25, abut the edge of the membrane to the anchoring leg. The connection with the profile is established with the sealing band Schlüter®-KERDI. Use the sealant adhesive Schlüter®-KERDI-COLL or the installation adhesive Schlüter®-KERDIFIX to attach the sealing band, with an overlap of at least 5 cm on Schlüter®- DITRA 25. The sealing band should reach the angled edge of Schlüter®- BARA-RT.
  4. The tiles are now installed, leaving a suitable space to the anchoring leg, which is to be filled with grout.

 

Installation in screed

  1. Schlüter®-BARA-RT is attached at the desired level in the edge area on a layer of screed and aligned. Pre-formed corners are available for external corners. A distance of approx. 5 mm should be left between profile ends, with the gap covered by clip-on connectors.
  2. A load distribution layer is now formed by installing a screed mortar, which is sloped to end flush with the upper edge of the Schlüter®-BARA-RT profile or lower, deducting the thickness of the tiles to be installed. A space of 3 mm below the upper edge of the profile must be left for the installation of the uncoupling and waterproofing membrane Schlüter®- DITRA 25.

 

Note: Schlüter®-TROBA or Schlüter®- TROBA-PLUS should be installed between the waterproofing assembly and the screed as an area drainage.


Contact Schlüter-Systems Ltd

Units 3-5 Bardon 22,
Beveridge Lane, Coalville,
Leicestershire, LE67 1TE
Phone: +44 (0) 1530 813396

Quick contact list

Reach the department of your choice directly via email:

image
Write To Us!

Do you have a question or suggestion?

Further information

on our products and specifications can be found here:

Schlüter colour key
Schlüter colour key

From brilliant white to brick red - here you will find an overview of all available product colours.

Legend "Products"

We use the following symbols and abbreviations to illustrate our price charts.

image image

= new products

= radius perforation available   

 

Dimensions:
H = height
L = length
B = width


Packaging:
PL = euro pallet 
KV = case packaging 
BV = bundle (there is a 10 item bundle packaging for all the profile types)
P = box packaging 
R = roll
St. = unit  


Schlüter® profiles with radius perforations
Schlüter® profiles with radius perforations