Cookies on the Schlüter-Website

Cookies help us deliver our services. By using our services, you agree to our use of cookies. Further information

logo

Schlüter®-BARA-RKK/-RKKE

Installation of Schlüter®-BARA-RKK

  1. Select Schlüter®-BARA-RKK according to the tile thickness.
  2. As an angled finishing profile, Schlüter®-BARA-RKK is embedded into the thin-set adhesive setting material with the trapezoid perforated anchoring leg aligned at the edge of the screed. Completely cover the anchoring leg with adhesive. Seal the abutting seams of the profiles with the self-adhesive anchoring fleece Schlüter®-BARA-HV (see photo).
  3. Install Schlüter®-DITRA 25, abutting the anchoring leg. The connection with the profile is established with the seaming tape Schlüter®-KERDI-KEBA. Use the sealing adhesive Schlüter®-KERDI-COLL to attach the seaming tape with an overlap of at least 5 cm on Schlüter®-DITRA 25, covering the entire anchoring leg and reaching the angled edge of Schlüter®- BARA-RKK. The system is now ready for the installation of tiles in the thin bed adhesive in accordance with the installation instructions of data sheet 6.1, Schlüter®-DITRA 25. Maintain a proper joint between the tiles and the anchoring leg of Schlüter®-BARA-RKK, to be filled with elastic grout.
  4. If using a trowel-applied sealing compound, align the trapezoid perforated anchoring leg of Schlüter®-BARA-RKK in the waterproofing assembly at the exposed edge. The waterproofing material must reach the angled edge of the profile. Observe the installation instructions of the manufacturer for the installation of bonded waterproofing systems.


Installation of Schlüter®-BARA-RKKE

  1. Select Schlüter®-BARA-RKKE according to the tile thickness.
  2. As an angled finishing profile, Schlüter®-BARA-RKKE is embedded into the thin bed adhesive setting material with the trapezoid perforated anchoring leg aligned at the edge of the screed. Completely cover the anchoring leg with adhesive. Seal the abutting seams of the profiles with the self-adhesive anchoring fleece Schlüter®-BARA-HV (see photo).
  3. Use the sealing adhesive Schlüter®-KERDI-COLL to adhere Schlüter®-KERDI, covering the entire anchoring leg and reaching the angled edge of Schlüter®-BARA-RKKE.
  4. If using a trowel-applied sealing compound, align the trapezoid perforated anchoring leg of Schlüter®-BARA-RKKE in the waterproofing assembly at the exposed edge. The waterproofing material must reach the angled edge of the profile. Observe the installation instructions of the manufacturer for the installation of bonded waterproofing systems.
  5. The bonded drainage membrane Schlüter®-DITRA-DRAIN is adhered over the bonded waterproofing assembly. Make sure to continue the membrane to below the joint spacer integrated in the profile. The profile heights 21 and 23 mm are also suitable for use with Schlüter®-DITRA-DRAIN 8. It must be assured that the drainage space is not fully closed, including during the installation of the covering materials.
  6. The system is now ready for the installation of tiles in the thin bed adhesive in accordance with the installation instructions of data sheet 6.2 Schlüter®-DITRA-DRAIN. Maintain a proper joint between the tiles and the anchoring leg of Schlüter®-BARA-RTKE, to be filled with elastic grouting.
    Note:
    Pre-formed parts are available for interior and exterior corners. Abut the profile ends of Schlüter®-BARA-RKK/-RKKE, leaving a joint of approx. 5 mm, which is to be covered by clip-on connectors. The applicable installation instructions and guidelines for the covering assemblies must be observed. All materials used in the assembly must be weather-resistant, waterproof, and suitable for outdoor areas.

Contact Schlüter-Systems Ltd

Units 3-5 Bardon 22,
Beveridge Lane, Coalville,
Leicestershire, LE67 1TE
Phone: +44 (0) 1530 813396

Quick contact list

Reach the department of your choice directly via email:

image
Write To Us!

Do you have a question or suggestion?

Further information

on our products and specifications can be found here:

Metal surfaces
Metal surfaces

All surfaces at a glance

Legend "Products"

We use the following symbols and abbreviations to illustrate our price charts.

image image

= new products

= radius perforation available   

 

Dimensions:
H = height
L = length
B = width


Packaging:
PL = euro pallet 
KV = case packaging 
BV = bundle (there is a 10 item bundle packaging for all the profile types)
P = box packaging 
R = roll
St. = unit