Schlüter®-BARA-RAK | Schlüter-Systems


Application and Function

Schlüter-BARA-RAK is a finishing profile with drip lip for the exposed edges of balconies and terraces that have an existing sloped screed.

The projecting bonding flange is recessed to allow for the use of the Schlüter-RONDEC or Schlüter-JOLLY protective edge profiles, which are available in the same colours as the balcony edging profile.

The trapezoid perforated anchoring leg of Schlüter-BARA-RAK is attached along the edge of the screed bed using an appropriate thin bed adhesive.

Schlüter-DITRA 25 can be installed as a waterproofing membrane, as can trowel applied waterproof membranes from other manufacturers or waterproofing layers compliant with DIN 18531. Schlüter-BARA-RAK results in a clean edge finish and protects the open screed edges from weather and corrosion.



  1. Schlüter-BARA-RAK is used as an edging and finishing profile, and is attached by embedding the trapezoid perforated anchoring leg into a thin bed of fresh adhesive along the edge area.
  2. Schlüter-DITRA 25 must abut the profile edge. Use Schlüter-KERDI-BAND to join the matting with the profile. Use the sealing adhesive Schlüter-KERDICOLL- L or the installation adhesive Schlüter-KERDI-FIX to attach the sealing band with an overlap of at least 5 cm on Schlüter-DITRA 25 and to the undercut profile of the protruding adhesive flange of Schlüter-BARA-RAK. The tiles may now be set in a thin adhesive bed while observing the manufacturer’s instructions for Schlüter-DITRA 25 included in product data sheet 6.1. The edge of the covering assembly should be approximately flush with the drip lip of Schlüter-BARA-RAK. If the Schlüter-RONDEC or Schlüter-JOLLY protective edge profile is used, apply tile adhesive on top of Schlüter-KERDI-KEBA and solidly embed the profile.
  3. If a trowel applied waterproof membrane is used, attach Schlüter-BARA-RAK at the exposed edge areas by integrating the trapezoid perforated anchoring leg into the waterproofing layer. The waterproof layer is carried over the cut back ribs of the projecting bonding flange. Observe manufacturer’s instructions for installing waterproof compounds.
  4. For waterproofing layers in accordance with DIN 18531, the trapezoid perforated anchoring leg of Schlüter-BARA-RAK must be attached along the open edge of the sloped screed using an appropriate thin-bed mortar. Apply a gradient layer at the transition area between the anchoring leg and the sloped screed to avoid a slope reduction. The waterproof membrane to be applied is carried over the cut back ribs of the projecting bonding flange and adhered, ensuring a watertight connection.
  5. Over waterproof layers in accordance with DIN 18531, an assembly conforming to norms and standards currently in effect is applied. This can be the application of a drainage layer with subsequent installation of a load distribution or gravel layer, or large format surface coverings supported by pedestals.
  6. Note: Prefabricated corners and connectors are available for internal and external corners. Abut the profile ends of Schlüter- BARA-RAK, leaving approx. a 5 mm wide joint. Cover the joint with the snap-on connector.
    When using an edge protection profile, the connector should be shortened at the intended breakage point and adhered to the edge profile using a suitable silicone, (see illustration 1).
    All current installation instructions and manufacturer’s guidelines for the covering type must be observed. All materials must be weather resistant, waterproof, and suitable for outdoor areas.

Abbildung 1



The profile is available in the following material version:

  • AC = colour coated aluminium

Material properties and areas of application

The coating of the aluminium profile is colour- fast, weather and UV resistant. Visible surfaces should be protected against abrasion.

In special cases, the suitability of Schlüter- BARA-RAK must be verified based on the anticipated chemical, mechanical, and/or other stresses.



Schlüter-BARA-RAK requires no special maintenance or care. The coated surface of the aluminium profile is colourfast and UV resistant. Damaged visible surfaces can be restored with paint.




Note: Schlüter®-BARA-RAK is not designed for attaching the Schlüter®-BARIN gutter systems, however, it is feasible by drilling holes (Ø 7 mm).


** to complete the Art.-No., add the colour (e.g. V / RKK 10 SB).

BW - brilliant white, RAL 9003
GM - grey metallic, RAL 9006
HB - light beige, RAL 1019
PG - pastel grey, no RAL
RB - red brown, RAL 8003
SB - black brown, RAL 8019







Contact Schlüter-Systems Ltd

Units 3-5 Bardon 22,
Beveridge Lane, Coalville,
Leicestershire, LE67 1TE
Phone: +44 (0) 1530 813396

Quick contact list

Reach the department of your choice directly via email:

Write To Us!

Do you have a question or suggestion?

Further information

on our products and specifications can be found here:

Schlüter colour key
Schlüter colour key

From brilliant white to brick red - here you will find an overview of all available product colours.

Legend "Products"

We use the following symbols and abbreviations to illustrate our price charts.

image image

= new products

= radius perforation available   


H = height
L = length
B = width

PL = euro pallet 
KV = case packaging 
BV = bundle (there is a 10 item bundle packaging for all the profile types)
P = box packaging 
R = roll
St. = unit